Williams 'B' Series Belt-Drive Horizontal Air Handler, Right Piping, 115V, 6 Coil Rows (CW or HW) - 1,600 CFM, 172,339 BTU
Williams 'B' Series Belt-Drive Horizontal Air Handler, Right Piping, 115V, 6 Coil Rows (CW or HW) - 1,600 CFM, 172,339 BTU
-
Product Description
-
Specs
-
Reviews
-
1
Product Q&A
-
Recommended Accessories
-
How-To Articles
-
Manuals
Features
Features
A Horizontal model of Belt-Driven Air Handlers for both hydronic and DX applications, these rugged units are dependable air handlers. Housed in a heavy-gauge, galvanized steel cabinet. Controls and motors are factory-mounted and provided in a single-point power supply. Access doors are provided on both sides of the unit for easy maintenance.
- Williams B162601R00 Features
- Heavy-gauge galvanized steel cabinet insulated with 1/2" thick, over three-pound density, neoprene-coated fiberglass.
- Two-pipe or Four-pipe hydronic heating and/or cooling. Four pipe systems may be converted to a two-pipe system by capping off one set of pipes.
- Coils are 1/2" OD copper tubes with aluminum fins (10 FPI) equipped with manual-air vent. Coils are 100% underwater pressure tested at 350 PSI with a 300 PSI working pressure.
- Galvanized drain pan features powder-coated epoxy with 1/4" thick elastomeric insulation and has primary and secondary drain connections.
- Belt-driven, draw-through design with forward-curved and dynamically balanced blowers.
- Wide range of motor sizes and adjustable, variable-pitch drive sheave and cast-iron pulley keyed to motor shaft (ordered separately & required for operation).
- Two-inch thick, 30/30 pleated filter, flatly mounted, with spring-loaded clips on each side of the access door for easy maintenance without the use of tools.
Product Note
Williams B162601R00 Compatible Sheave Kits:Kit Model # at Horsepower @ Inches of Static Pressure
- S2 operating at 3/4 hp @ 0.0
- S2 operating at 3/4 hp @ 0.1
- S2 operating at 3/4 hp @ 0.2
- S3 operating at 3/4 hp @ 0.3
- S3 operating at 3/4 hp @ 0.4
- S3 operating at 3/4 hp @ 0.5
- S4/S51* operating at 1 hp @ 0.6
- S4/S51* operating at 1 hp @ 0.7
- S4/S51* operating at 1 hp @ 0.8
- S4/S51* operating at 1 hp @ 0.9
- S5/S50* operating at 1 hp @ 1.0
* Use with 3-phase motors only
Specifications
General Information
Blower Motor
Variable Speed
Configuration
Orientation describes the direction that air will flow through a piece of equipment. (e.g. air will flow horizontally through a "Horizontal" unit heater.) Most equipment will only function properly if installed in the proper orientation.
Horizontal
Additional Model Numbers
B162601R00, AH016W2B601R00
Performance
Nominal Maximum Cooling Capacity
59436 BTU
Maximum Air Flow
1600 CFM
Electrical Data
Dimensions
Product Weight
290 Pounds
Warranty Information
Parts Warranty
A warranty is a safeguard from defects in manufacturing and can vary in length and terms. To see the manufacturer's warranty statement, click on the Manuals tab. Learn More
1 Year
Features
Features
A Horizontal model of Belt-Driven Air Handlers for both hydronic and DX applications, these rugged units are dependable air handlers. Housed in a heavy-gauge, galvanized steel cabinet. Controls and motors are factory-mounted and provided in a single-point power supply. Access doors are provided on both sides of the unit for easy maintenance.
- Williams B162601R00 Features
- Heavy-gauge galvanized steel cabinet insulated with 1/2" thick, over three-pound density, neoprene-coated fiberglass.
- Two-pipe or Four-pipe hydronic heating and/or cooling. Four pipe systems may be converted to a two-pipe system by capping off one set of pipes.
- Coils are 1/2" OD copper tubes with aluminum fins (10 FPI) equipped with manual-air vent. Coils are 100% underwater pressure tested at 350 PSI with a 300 PSI working pressure.
- Galvanized drain pan features powder-coated epoxy with 1/4" thick elastomeric insulation and has primary and secondary drain connections.
- Belt-driven, draw-through design with forward-curved and dynamically balanced blowers.
- Wide range of motor sizes and adjustable, variable-pitch drive sheave and cast-iron pulley keyed to motor shaft (ordered separately & required for operation).
- Two-inch thick, 30/30 pleated filter, flatly mounted, with spring-loaded clips on each side of the access door for easy maintenance without the use of tools.
Product Note
Williams B162601R00 Compatible Sheave Kits:Kit Model # at Horsepower @ Inches of Static Pressure
- S2 operating at 3/4 hp @ 0.0
- S2 operating at 3/4 hp @ 0.1
- S2 operating at 3/4 hp @ 0.2
- S3 operating at 3/4 hp @ 0.3
- S3 operating at 3/4 hp @ 0.4
- S3 operating at 3/4 hp @ 0.5
- S4/S51* operating at 1 hp @ 0.6
- S4/S51* operating at 1 hp @ 0.7
- S4/S51* operating at 1 hp @ 0.8
- S4/S51* operating at 1 hp @ 0.9
- S5/S50* operating at 1 hp @ 1.0
* Use with 3-phase motors only
Specifications
General Information
Blower Motor
Variable Speed
Configuration
Orientation describes the direction that air will flow through a piece of equipment. (e.g. air will flow horizontally through a "Horizontal" unit heater.) Most equipment will only function properly if installed in the proper orientation.
Horizontal
Additional Model Numbers
B162601R00, AH016W2B601R00
Performance
Nominal Maximum Cooling Capacity
59436 BTU
Maximum Air Flow
1600 CFM
Electrical Data
Dimensions
Product Weight
290 Pounds
Warranty Information
Parts Warranty
A warranty is a safeguard from defects in manufacturing and can vary in length and terms. To see the manufacturer's warranty statement, click on the Manuals tab. Learn More
1 Year
Specifications
General Information
Blower Motor
Variable Speed
Configuration
Orientation describes the direction that air will flow through a piece of equipment. (e.g. air will flow horizontally through a "Horizontal" unit heater.) Most equipment will only function properly if installed in the proper orientation.
Horizontal
Additional Model Numbers
B162601R00, AH016W2B601R00
Performance
Nominal Maximum Cooling Capacity
59436 BTU
Maximum Air Flow
1600 CFM
Electrical Data
Dimensions
Product Weight
290 Pounds
Warranty Information
Parts Warranty
A warranty is a safeguard from defects in manufacturing and can vary in length and terms. To see the manufacturer's warranty statement, click on the Manuals tab. Learn More
1 Year
Be the First to Write a Review
Do you own this product?
Please share your insights with fellow shoppers.
Search Product Q&A's
Answered by Bob, the Heating Product Expert
+−
Can this unit be used with a heat pump?
David
from Georgia
February 24, 2016
Answer
The B-series air handler is designed for use with either hot or chilled water to provide both heating and cooling. It will work with a geothermal or air-to-water heat pump, but not with a air-to-air DX heat pump.
Recommended Accessories
+−
Expert Recommended Accessories
Hand Picked By Our Expert Bob